56 Questions and Answers about the Amplitude Modulation (AM)Interview |

Analog modulator manufacturer from

11.06.2019 10:08:57 - Amplitude modulation is one of the easiest signal modulation forms to execute; in terms of power usage and spectrum efficiency, it is not the most important.

( - Amplitude modulation is one of the easiest signal modulation forms to execute; in terms of power usage and spectrum efficiency, it is not the most important. As a result, the use of amplitude modulation is coming into preference to other analogue modes such as frequency modulation, and a numerous digital modulation formats. Yet in spite of this decrease, amplitude modulation


is in such extensively used, particularly for broadcasting, and many amplitude modulation signals can be heard on the several long, medium and short wavebands where they will unquestionably be heard for many years to come.

HDMI Encoder Modulator, 16in1 Digital Headend, HD RF Modulator at

Amplitude Modulation (AM) Interview Questions

Skype: soukaken

Source:wisdom jobs Answer:

Modulation is required to send the information over long distances as low frequency signals are not able to cover large area.

While demodulation is required to get back the information sent at the receiving side.

Source:wisdom jobsQuestion 4: Why Frequency Modulation Is Better Than Amplitude Modulation?


Modulation is better as it provide more resistance to noise as compared to demodulation.

Question 5: What Is Digital Modulation And State Various Techniques?

Source:wisdom jobs

Question 6: State the Techniques of Demodulation?


There are several ways of demodulation depending on how parameters of the carrier signal, such as amplitude, frequency or phase.

a) For a signal modulated with a linear modulation, like AM, we can use a synchronous detector.

Source:wisdom jobsAnswer:

A detector is a device that recovers information of interest contained in a modulated wave.

Demodulation is updated form of detector which extracts the original information from a modulated carrier wave.

Question 9: What Is Depth Of Modulation?


It refers to the ratio of the un-modulated carrier amplitude to the amplitude deviation for which the modulated carrier wave reaches its minimum value.

Question 10: What Is The Difference Between Coherent And Non-coherent Demodulation?


In case of coherent, carrier used for demodulation purpose is in phase and frequency synchronism with carrier used for modulation purpose while for non-coherent, it is not in synchronism.

Question 11: Calculate The Power In One Of The Side Band In Ssbsc Modulation When The Carrier Power Is 124w And There Is 80% Modulation Depth In The Amplitude Modulated Signal?


Modulation Index = 0.8

Pc = 124W

Power in sidebands may be calculated as = m2 Pc/4

= (0.8)2 * 124/4

= 79.36 W

Question 12: Advantages Of Analog Communication Over Digital Communication Are?


Due to analog to digital conversion, the data rate becomes high in digital communication. So the transmission bandwidth is also increased. Digital transmission also needs synchronization in certain applications which is not needed in case of analog communication systems.

Question 13: What Is The Carrier Frequency In An Am Wave When Its Highest Frequency Component Is 850 Hz And The Bandwidth Of The Signal Is 50 Hz?


Upper frequency = 850Hz

Bandwidth = 50Hz

Therefore lower Frequency = 850 - 50= 800 Hz

Carrier Frequency = (850-800)/2

= 825 Hz

Question 14: In Terms of Signal Frequency (fs) And Intermediate Frequency (fi), The Image Frequency Is Given By?


The image frequency is defined as the signal frequency added to twice the value of intermediate frequency. It is the undesirable frequency generated at the receiver which also gets amplified with the message signal. The image frequency causes interference and therefore two or more stations or sources may be received simultaneously at the receiver output.

Question 15: Cross Talk Is?


Cross talk is the disturbance caused in the nearby channel or circuit due to transmitted signal. Cross talk is usually caused by undesired coupling of capacitors or inductors from one channel to another. Electromagnetic interference (EMI) causes cross talk in the circuits or the channels. In crosstalk, the signals traveling closer to each other interfere with each other and cause disturbance in the signal.

Question 16: The Costas Receiver Is Used For?


Costas receiver is a synchronous receiver system used for demodulating DSB-SC waves. The incoming modulated carrier is applied at two inputs of the coherent detectors of the receiver. The locally generated carrier applied to the two inputs is however in phase quadrature with each other. The frequencies of the local carriers are adjusted as same as the carrier frequency of the received signal.

Question 17: The Advantages Of Using An RF Amplifier Are?


The RF amplifiers are used in super heterodyne receivers. The advantages of using RF receivers are

They have better sensitivity i.e. they have improved gain to the signal

They have better signal to noise ration than other amplifiers

The selectivity is better as they have better rejection to the adjacent undesired signals.

Question 18: Function Of Frequency Mixer In Super Heterodyne Receiver is?


The function of a frequency mixer in a super heterodyne receiver is that it mixes or multiplies the incoming modulated carrier with the locally generated carrier. It then produces a number of frequencies. The produced frequencies are either the sum or the differences of the frequencies of the received signals. The output of the mixer is used to detect the modulating or information signal from the received modulated carrier.

Question 19: The Functions Of Radio Receiver Are?


The radio receivers receive the incoming modulated carrier by the receiving antennas. Then they select the wanted signal from the carrier and reject the unwanted signals and noise. The received signal is then amplified by the RF amplifiers. Detection of the information signal is done from the received carrier and the information or the modulating signal is then filtered and amplified.

Question 20: The Standard Value For Intermediate Frequency (if) In Am Receivers Is?


Intermediate frequency (IF) is a frequency at which the received carrier frequency is shifted for detection of message signal. The IF is generated by mixing the received carrier with the locally generated signal. The IF is generated and is shifted to further amplifiers and detectors for amplification and detection of message signal respectively. In super heterodyne AM receivers, an intermediate frequency of 455 KHz is used.

Question 21: Intermediate Frequency (if) Should Be Carefully Chosen As?


Intermediate frequency (IF) should be carefully chosen as

High IF results in poor selectivity and therefore poor rejection of adjacent channels.

High IF results in problems in tracking of signals in the receivers.

Image frequency rejection becomes poor at low IF or if very high.

Question 22: Advantages of Using An RF Amplifier Are?


The RF amplifiers have greater gain that is they have better sensitivity. They have better ability to amplify weak signals received by the receiver. The RF amplifiers have better selectivity i.e., better ability to select the wanted signals among the various incoming signals. The incoming weak signals are raised to a higher level by the RF amplifiers and therefore they improve signal to noise ratio.

Question 23: Selectivity of a Receiver?


The ability of the receiver to select the wanted signals among the various incoming signals is termed as Selectivity. It rejects the other signals at closely lying frequencies. Selectivity is determines performance of a radio receiver that how much it responds only to the radio signal that is required to receive. Selectivity of a receiver changes with incoming signal frequency and is poorer at high frequencies.

Question 24: The Factors That Determine The Sensitivity Of Super Heterodyne Receiver Are?


Sensitivity of a receiver is defined as the ability of the receiver to amplify weak signals received by the receiver. It is the voltage that must be applied at the input terminals of the receiver to achieve a minimum standard output at the output of the receiver. The factors that determine the sensitivity of super heterodyne receiver are?

Gain of the IF amplifier

Noise figure of the receiver

Gain of RF amplifier

Question 25: In Automatic Gain Control of The Am Receiver?


The automatic gain control (AGC) circuit is used to adjust the gain of the receiver depending upon the strength of the received signal at the receiver. The AGC gives a DC voltage as an output that is proportional to the amplitude of the received signal. In AGC, the output is a linear function of the input.

Question 26: Squelch Circuit Is?


Squelch circuit suppresses the output audio when there is insufficient desired input signal at the receiver. The circuit is used to suppress the unwanted channel noise when there is no reception by the receiver. Squelch circuits may be used in wireless microphones stay away from replicating the noise when enough signal is not received. Regulating squelch is provided in some systems for the receiver.

Question 27: Frequency Components Of An Am Wave (m = Modulation Index) Are?


Frequency components of an AM wave having m modulation index are

Carrier frequency (ωc ) with amplitude A

Upper side band (ωc + ωm) having amplitude mA/2

Lower side band (ωc - ωm) having amplitude mA/2

Question 28: Examples Of Low Level Modulation Are?


In a Low level Amplitude Modulation system, modulation is done at lower power of carrier and modulating signal. Therefore the output power of modulation is low. So power amplifiers are required to boost the signal up to the desired power level. Examples of low level modulation are

Square law diode modulation

Switching modulation

Question 29: If Modulation Index Is Greater Than 1?


Modulation index is the measure of extent to which the parameter of the carrier is varied in accordance with the modulating signal. If modulation index is greater than 1, or the modulation percentage is more than 100%, it is called over modulation.

The baseband signal is not preserved in the envelope of the AM signal and therefore, the recovered signal is distorted at the output of the receiver.

Question 30: In An Amplitude Modulation?


In an Amplitude Modulation, the amplitude of the carrier varies according to the instantaneous values of the baseband signal. The frequency and the phase of the carrier remain constant.

The envelope of the AM wave has the same shape as the message of the base band signal.

Question 31: Automatic Gain Control Is?


Automatic gain control provides controlled signal amplitude at the output even if there are amplitude variations at the input. This controlled output adjusts the input to output gain to a suitable value so that the system may work properly even for wide range of variations at the input.

The AGC is used in AM radio receivers for controlling the weak and strong sound signals.

Question 32: Vestigial Side Band Signals Are Detected By?


Vestigial side band signals are detected by Synchronous detection or coherent detection technique. The distortions in a VSB signal may be reduced by reducing the modulation index and increasing the width of VSB.

Question 33: Phase Shift Method Is?


Phase shift method is one of the methods used for the generation of SSB-SC signals. This method includes two balanced modulators and two phase shifting networks and avoids the use of filters. Both the balanced modulators produce side band as an output.

The SSB-SC signals are generated using multiple tone modulating signals as if done with single tone modulating signal, they do not carry any useful information.

Question 34: Limitations Of Frequency Discrimination Method Are?


Limitations of Frequency discrimination method are that as the base band signal must be appropriately related to the carrier signal frequency, the designing of band pass filter is difficult if the carrier frequency is quite higher than the bandwidth of the baseband signal. The system is not useful for video communication purpose.

Question 35: Generation Of Ssb Sc Signal Is Done By?


SSB-SC signals are the signals where only one of the sidebands is transmitted in an AM wave. The carrier is also suppressed while transmitting the AM signal. SSBSC signal may be generated by two methods:

Frequency discrimination method or filter method

Phase discrimination method or phase shift method

Question 36: Pilot Carrier Is?


Pilot carrier is a small carrier transmitted with modulated signal from the transmitter. It is separated at the receiver and used to phase lock the locally generated carrier signal generated at the receiver. It provides synchronization at the receiver.

As a weak carrier is transmitted with the DSB signal, it is also referred to as partially suppressed carrier system, as the carrier is not totally suppressed. So it is a case of over modulation.

Question 37: Quadrature Amplitude Modulation (QAM) Is?


The modulation scheme Quadrature Amplitude Modulation (QAM) enables same bandwidth used for transmission of two DSB-SC signals. It is also known as Bandwidth Conservation scheme. However it needs synchronous detection so it needs an additional system for generation of carrier. Also known as Quadrature Carrier Multiplexing, the scheme is used in color television.

Question 38: Disadvantages Of Using Synchronous Detection Of Am Signal Are?


Disadvantages of using synchronous detection of AM signal are that it needs an additional system for generation of carrier. The frequency of the locally generated carrier must be identical to that of transmitted carrier. And the phase of the locally generated carrier must be synchronized to that of transmitted carrier otherwise the detected signal would get distorted so it needs an additional system for synchronization of carrier. This makes the receiver complex and costlier.

Question 39: Requirements Of Synchronous Detection Of Am Signal Are?


Synchronous detection of AM signal requires local generation of the carrier signal at the receiver. The frequency of the locally generated carrier must be identical to that of transmitted carrier. And the phase of the locally generated carrier must be synchronized to that of transmitted carrier otherwise the detected signal would get distorted.

Question 40: In Synchronous Detection Of Am Signal?


In synchronous detection of AM signal, the carrier signal is locally generated and then passed through a low pass filter. At the output of the low pass filter, the original modulating signal is recovered. The synchronous detection requires the generation of carrier at the receiver also. So additional circuitry is required at the receiver.

Question 41: What Is The Maximum Transmission Efficiency Of An Am Signal?


The transmission efficiency (η) of AM wave is defined as the percentage of total power contributed by side bands of the AM signal. The maximum transmission efficiency of an AM signal is 33.33%, i.e., only one third of the total transmitted power is carried by the side bands in an AM wave. The remaining two third of the total transmitted power gets wasted.

Question 42: Ring Modulator Is


Ring modulator is a product modulator used for DSB SC generation. It consists of four diodes connected in the form of ring. In AM, the ring modulator acts as a product modulator for a square wave carrier and modulating signal and generated a Double Side Band-Suppressed Carrier signal.

Question 43: The Process Of Recovering Information Signal From Received Carrier Is Known As?


Detection or demodulation of the received signal is the recovery of information or the original message that was transmitted by the transmitter after modulation. The process is also called demodulation it recovers the original signal from the modulated signal received.

Question 44: Am Demodulation Techniques Are?


AM signals are detected or demodulated using Square law demodulator or envelope detector. The demodulators extract the information from the received AM signal.

Square law demodulators are highly nonlinear in low voltage region so they are used for low level modulated signals. Envelope detectors extract the envelope of the AM wave.

Question 45: In High Level Amplitude Modulation?


In High level Amplitude Modulation system, Modulation is done at high power of carrier and modulating signals so Power amplifiers are used to boost the carrier and modulating signals before modulation. Collector modulation method is the example of High level Amplitude Modulation.

Question 46: In Low Level Amplitude Modulation?


In a Low level Amplitude Modulation system, modulation is done at lower power of carrier and modulating signal. Therefore the output power of modulation is low. So power amplifiers are required to boost the signal up to the desired power level.

Question 47: An Oscillator for an Am Transmitter Has A 100μh Coil and A 10nf Capacitor. If A Modulating Frequency Of 10 KHz Modulates The Oscillator, Find The Frequency Range Of The Side Bands?


Carrier frequency fc = 1/2Π√LC

= 1/ 2Π√100 * 10 - 6 * 10 * 10-9

= 1/2Π * 10-6

= 1.59 * 105 Hz

= 159 KHz

The modulating frequency FM is 10 KHz

Therefore the range of AM spectrum is given by (fc FM ) to (fc + FM )

= (159 - 10) to (159 + 10)

= 149 KHz to 169 KHz

Question 48: Bandwidth (b) Of An Am Signal Is Given By?


Bandwidth of the AM wave is the difference in the two extreme frequencies of the AM signal. It is given by

B = (ωc + ωm) - (ωc - ωm)

= ωm

i.e., the bandwidth of the AM wave is twice the highest frequency present in the modulating signal.

Question 49: Am Wave May Be Represented As E(t) Cos ωct Where E(t) Is


An AM wave may be represented by

s (t) = [A+ x(t)] cos ωct

= E (t) cos ωct

Where x (t) is the modulating signal

A is the amplitude of carrier wave

E(t) is the Envelope of the AM wave

The envelope consists of the modulating signal that may be recovered from AM signal using demodulation techniques.

Question 50: Radio Waves Travel Through?


Radio communication or wireless communication takes place through electromagnetic waves.

The message is transmitted through open space via electromagnetic waves or radio waves. The waves are transmitted in the open space through antenna after processing of signal.

Question 51: The Minimum Antenna Height Required for Transmission In reference To Wavelength λ is?


For effective transmission of signal by the transmitter, the antenna height should be at least quarter length of the signal wavelength i.e., λ/4

L= λ/4

= c/4f

Required antenna height decreases with increase in frequency of the signal so modulation is done. With modulation, the low frequency signals are shifted to high frequency signals.

Question 52: Analog Signal May Be Converted Into Digital Signal By?


Conversion of analog signal into digital signal converts a continuous time signal in the form of digits. The conversion is done with the help of sampling technique. A sample is a set of values at a point in time space. The average number of samples obtained in one second is known as sampling frequency.

Question 53: Synchronous Detection Means?


Synchronous detection means demodulation of received signal and extracting information from it. It requires a reference signal at the receivers with predetermined frequency and phase which is generated using extra circuitry. Synchronous detection helps in extracting weak signals from noise.

Question 54: What Is The Effect On The Transmitted Power Of Am Signal When The Modulation Index Changes From 0.8 To 1?


The total power in an AM is given by

Pt. = Pc (1 + m2/2)

Where Pc is the carrier power and m is the modulation index.


Pt1 = Pc (1 + 0.82/2) = 1.32 Pc

Pt2 = Pc (1 + 12/2) = 1.5 Pc

Increase in power = (1.5 Pc - 1.32 Pc)/ 1.32 Pc

= 0.1364

Question 55: Types Of Analog Modulation Are?


Modulation is a process by which some characteristics of signal such as amplitude or phase or frequency are varied in accordance with the instantaneous value of the information signal.

The signal whose characteristics are varied is known as carrier signal, as it carries the information. The signal that carries the information is known as modulating signal as according to it, the characteristics of carrier signal are varied.

Methods of analog modulations are:

Amplitude modulation

Frequency modulation

Phase modulation

Question 56: Analog Communication Indicates?


Analog communication means that the information is transmitted in the form of a continuous signal, such as a sound wave. The signal has varying amplitude or phase or frequency.

Coding is not applied to the signal as in case of digital data. Amplitude modulated signal and frequency modulated signals are the examples of analog communication.

Established in 2000, the main products are modulators both in analog and digital ones, amplifier and combiner. We are the very first one in manufacturing the headend system in China. Our 16 in 1 and 24 in 1 now are the most popular products all over the world.

For more, please access to


Dingshengwei Electronics Co., Ltd

Company Address: Building A, the first industry park of Guanlong, Xili Town, Nanshan, Shenzhen, Guangdong, China

Tel: +86 0755 26909863

Fax: +86 0755 26984949

Phone: +86 13410066011

Source: wisdom jobs

Press Information:
Dingshengwei Electronics Co., Ltd

Contact Person:

Phone: 13410066011
eMail: eMail

Web: http://


Disclaimer: If you have any questions regarding information in this article please contact the author. Please do not contact We are not able to assist you. disclaims content contained in this article. is not authorized to give any information about content and not responsible for content posted by third party.
refer this article
Print This Article
Terms Of Use Privacy About Contact Us